Aruba 560 Series Wi-Fi 6 Access Point

• Built-in Omni Directional Antennas
• 5 GHz Antennas 5.4 dBi
• 2.4 GHz Antennas 3.2 dBi
• BLE/802.15.4 Antennas 3.3dBi

AP-567

• Built-in 90°H x 90°V Directional Antennas
• 5 GHz Antennas 6.8 dBi
• 2.4 GHz Antennas 7.1 dBi
• BLE/802.15.4 Antennas 3.0 dBi

WIRELESS RADIO SPECIFICATIONS

• Outdoor Hardened, Wi-Fi 6 dual radio, 5 GHz 2×2 MIMO and 2.4 GHz 2×2 MIMO

Software-configurable dual radio supports 5 GHz (Radio 0) and 2.4 GHz (Radio 1)

5GHz:

• Two spatial stream Single User (SU) MIMO for up to 1.2 Gbps wireless data rate with individual 2SS HE80 802.11ax client devices, or with two 1SS HE80 802.11ax MU-MIMO capable client devices simultaneously

2.4GHz:

• Two spatial stream Single User (SU) MIMO for up to 574 Mbps (287 Mbps) wireless data rate with individual 2SS HE40 (HE20) 802.11ax client devices or with two 1SS HE40 (HE20) 802.11ax MU-MIMO capable client devices simultaneously

Up to 256 associated client devices per radio

Up to 16 BSSIDs per radio

Supported frequency bands (country-specific restrictions apply):

• 2.400 to 2.4835 GHz
• 5.150 to 5.250 GHz
• 5.250 to 5.350 GHz
• 5.470 to 5.725 GHz
• 5.725 to 5.850 GHz
• 5.850 to 5.925 GHz
• 5.825 to 5.875 GHz

Available channels: Dependent on configured regulatory domain

Dynamic frequency selection (DFS) optimizes the use of available RF spectrum

Supported radio technologies:

• 802.11b: Direct-sequence spread-spectrum (DSSS)
• 802.11a/g/n/ac: Orthogonal frequency-division multiplexing (OFDM)
• 802.11ax: Orthogonal frequency-division multiple access (OFDMA) with up to 16 resource units (RU)

Supported modulation types:

• 802.11b: BPSK, QPSK, CCK
• 802.11a/g/n: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM (proprietary extension)
• 802.11ac: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM, 1024-QAM (proprietary extension)
• 802.11ax: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM, 1024-QAM

802.11n high-throughput (HT) support: HT 20/40

802.11ac very high throughput (VHT) support: VHT 20/40/80

802.11ax high efficiency (HE) support: HE20/40/80

Supported data rates (Mbps):

• 802.11b: 1, 2, 5.5, 11
• 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54
• 802.11n: 6.5 to 300 (MCS0 to MCS15, HT20 to HT40), 400 with 256-QAM
• 802.11ac: 6.5 to 867 (MCS0 to MCS9, NSS = 1 to 2, VHT20 to VHT80), 1,083 with 1024-QAM
• 802.11ax (2.4GHz): 3.6 to 574 (MCS0 to MCS11, NSS = 1 to 2, HE20 to HE40)

802.11n/ac/ax Packet aggregation: A-MPDU, A-MSDU

Transmit power: Configurable in increments of 0.5 dBm

Maximum (conducted) transmit power (limited by local regulatory requirements):

• 2.4 GHz band: +23 dBm per chain, +26 dBm aggregate (2×2)
• 5 GHz band: +23 dBm per chain, +26 dBm aggregate (2×2)
• Note: conducted transmit power levels exclude antenna gain.

Maximum EIRP (limited by local regulatory requirements):

• 2.4 GHz band:
  • 565: 29.2 dBm EIRP
  • 567: 33 dBm EIRP
• 5 GHz band:
  • 565: 31.4 dBm EIRP
  • 567: 32.7 dBm EIRP

Advanced Cellular Coexistence (ACC) minimizes interference from cellular networks

Maximum ratio combining (MRC) for improved receiver performance

Cyclic delay/shift diversity (CDD/CSD) to enable the use of multiple transmit antennas

Short guard interval for 20-MHz, 40-MHz, and 80-MHz

Space-time block coding (STBC) for increased range and improved reception

Low-density parity check (LDPC) for high-efficiency error correction and increased throughput

Transmit beam-forming (TxBF) for increased signal reliability and range

• 15.6W

Maximum (worst case) power consumption in idle mode:

• 4.2W

Maximum (worst case) power consumption in deep-sleep mode:

• 1.7

Power sources sold separately

Power over Ethernet (PoE+):

• 802.3at-compliant

When powered by 1x 802.3at, there are no restrictions

When powered by 1x 802.3af with IPM enabled, the AP will start up in unrestricted mode, but may dynamically apply restrictions depending on the POE budget and actual power. The feature restrictions can be programmed.

When powered by 1x 802.3af with IPM disabled, the AP will lower the 2.4Ghz radio to 1×1:1

• Auto-sensing link speed and MDI/MDX
• PoE-PD: 48Vdc (nominal) 802.3at/bt (Class 3 or higher)
• 802.3az Energy Efficient Ethernet (EEE)

Bluetooth 5 and 802.15.4 radio

• 2.4 GHz
• Bluetooth 5: up to 8 dBm transmit power and -95 dBm receive sensitivity
• Zigbee: up to 8 dBm transmit power and -97 dBm receive sensitivity
• Up to 4 dBm transmit power (class 2) and -91 dBm receive sensitivity

Visual indicator (multi-color LED): For system and radio status

Reset button: Factory reset (during device power up)

USB-C console interface

AP-270-MNT-V2

AP-270-MNT-H1

AP-270-MNT-H2

• Dimensions/weight (excluding mount):
  • 16.5 cm (W) x 16.5 cm (D) x 11 cm (H)
  • 6.5” (W) x 6.5” (D) x 4.3” (H)
  • 1.03 kg/2.27 lbs

AP-567

• Dimensions/weight (excluding mount):
  • 16.5 cm (W) x 16.5 cm (D) x 11 cm (H)
  • 6.5” (W) x 6.5” (D) x 4.3” (H)
  • 1.09 kg/2.4 lbs

• Temperature: -40° C to +55° C (-40° F to +140° F) with full solar loading
• Humidity: 5% to 95% non-condensing internal
• Rated for operation in all weather conditions

Storage and transportation:

• Temperature: -40° C to +70° C (-40° F to +158° F)

Operating Altitude: 3,000 m

Water and Dust: IP66/67

Salt Tolerance: Tested to ASTM B117-07A Salt Spray 200hrs

Wind Survival: Up to 165 Mph

Shock and Vibration ETSI 300-19-2-4

CE Marked

RED Directive 2014/53/EU

EMC Directive 2014/30/EU

Low Voltage Directive 2014/35/EU

UL/IEC/EN 60950

EN 60601-1-1, EN60601-1-2

For more country-specific regulatory information and approvals, please see your Aruba representative.

AP-567: APEX0567

UL2043 plenum rating

Wi-Fi Alliance certified 802.11a/b/g/n/

Wi-Fi Alliance certified Wi-Fi 6 (802.11ax)

Wi-Fi CERTIFIED™ ac (with Wave 2 features)

Passpoint® (Release 2) with ArubaOS and Instant 8.3+